Aviation Safety Action Message

CH-47-02-ASAM-04

 

         
CH-47 Aft Yoke Assembly.

 

         
CH-47 Aft Yoke Assembly.

 

         

UNCLASSIFIED

MSG DTG 241630Z JUL 02

FROM CDRAMCOM, REDSTONE ARSENAL, AL  //AMSAM-SF-A//

SUBJECT - AVIATION SAFETY ACTION MESSAGE (ASAM), MAINTENANCE 
MANDATORY, RCS CSGLD-1860(R1), ALL H-47 SERIES AIRCRAFT, 
INSPECTION FOR UNTESTED CRITICAL SAFETY ITEM (CSI), P/N 
114C3044-2, AFT YOKE SUPPORT SHAFT, CH-47-02-ASAM-04, 
(TB 1-1520-240-20-149) 
                              NOTE 
THIS ASAM IS ISSUED IAW AR 95-1, 1 SEP 97, CHAPTER 6.  THIS ASAM 
HAS NOT BEEN TRANSMITTED TO UNITS SUBORDINATE TO ADDRESSEES.  
ADDRESSEES SHOULD IMMEDIATELY RETRANSMIT THIS ASAM TO ALL 
SUBORDINATE UNITS, ACTIVITIES OR ELEMENTS AFFECTED OR CONCERNED.  
THE RETRANSMITTAL SHALL REFERENCE THIS ASAM.  ACTION ADDRESSEES 
WILL IMMEDIATELY VERIFY THIS TRANSMISSION TO CDR, AMCOM, ATTN:  
AMSAM-SF-A (SOF COMPLIANCE OFFICER).
1.  PRIORITY CLASSIFICATION -
                             NOTE 
IAW AR 95-1, PARAGRAPH 6-6A/6-14A, MACOM COMMANDERS MAY AUTHORIZE 
TEMPORARY EXCEPTION FROM THE REQUIREMENTS OF THIS ASAM.  
EXCEPTION MAY ONLY OCCUR WHEN COMBAT OPERATIONS OR MATTER OF LIFE 
OR DEATH IN CIVIL DISASTERS OR OTHER EMERGENCIES ARE SO URGENT 
THAT THEY OVERRIDE THE CONSEQUENCES OF CONTINUED AIRCRAFT 
OPERATION.
    A.  AIRCRAFT IN USE - UPON RECEIPT OF THIS MESSAGE, MAKE THE 
FOLLOWING ENTRY ON THE DA FORM 2408-13-1.  ENTER A RED HORIZONTAL 
DASH //-// STATUS SYMBOL WITH THE FOLLOWING STATEMENT: "INSPECT 
FOR UNTESTED CSI P/N 114C3044-2 AFT YOKE SUPPORT SHAFT IAW CH-47-
02-ASAM-04 (TB 1-1520-240-20-149) WITHIN THE NEXT 10 FLIGHT 
HOURS, BUT NLT 7 AUG 02."  REPLACE UNTESTED P/N 114C3044-2 AFT 
YOKE SUPPORT SHAFT AT THE NEXT PHASE INSPECTION INTERVAL, OR 
31 DECEMBER 2002, WHICHEVER OCCURS FIRST.  CLEAR THE RED 
HORIZONTAL DASH //-// ENTRY WHEN THE PROCEDURES IAW PARAGRAPHS 8 
AND 9 ARE COMPLETED.  THE AFFECTED AIRCRAFT SHALL BE INSPECTED AS 
SOON AS PRACTICAL BUT NO LATER THAN 7 AUG 02.  COMMANDERS WHO ARE 
UNABLE TO COMPLY WITH THE REQUIREMENTS OF THIS ASAM WITHIN THE 
TIME FRAME SPECIFIED WILL UPGRADE THE AFFECTED AIRCRAFT STATUS 
SYMBOL TO A RED //X//. 
    B.  AIRCRAFT IN MAINTENANCE - 
        (1)  AIRCRAFT IN AVUM, AVIM OR DEPOT LEVEL MAINTENANCE - 
SAME AS PARA 1A. 
        (2)  AIRCRAFT AT CONTRACTOR FACILITY - BOEING HELICOPTERS 
WILL INSPECT DD 250 AIRCRAFT PRIOR TO THOSE AIRCRAFT DEPARTING 
FOR FERRY TO FINAL DESTINATION. 
    C.  AIRCRAFT IN TRANSIT - 
        (1)  SURFACE/AIR SHIPMENT - SAME AS PARA 1A. 
        (2)  FERRY STATUS - SAME AS PARA 1A. 
    D.  MAINTENANCE TRAINERS (CATEGORY A AND B) - COMPLY NLT 
31 DECEMBER 2002.
    E.  COMPONENT/PARTS IN STOCK AT ALL LEVELS (DEPOT AND OTHERS) 
INCLUDING WAR RESERVES - UPON RECEIPT OF THIS MESSAGE, DEPOT AND 
MATERIEL ACTIVITY COMMANDERS WILL ENSURE THE MATERIEL CONDITION 
TAGS OF ALL ITEMS IN ALL CONDITION CODES LISTED IN PARAGRAPH 7 
ARE ANNOTATED TO READ:  "CH-47-02-ASAM-04 (TB 1-1520-240-20-149) 
INSPECTION FOR UNTESTED CSI P/N 114C3044-2 AFT YOKE SUPPORT 
SHAFT, NOT COMPLIED WITH." 
        (1)  WHOLESALE STOCK - N/A. 
        (2)  RETAIL STOCK - UPON RECEIPT OF THIS ASAM, COMMANDERS 
AND FACILITY MANAGERS MAINTAINING RETAIL STOCK AT INSTALLATION 
LEVEL AND BELOW SHALL CONTACT THE SUPPORTED AVIATION UNIT TO 
PERFORM THE PROCEDURES REQUIRED IAW PARAGRAPHS 8 AND 9 ON SUSPECT 
MATERIEL.  DISPOSE OF DISCREPANT MATERIEL IAW PARAGRAPH 10D.  
REPORT COMPLIANCE WITH THIS MESSAGE IAW PARAGRAPH 14C(2) NLT 5 
AUG 02.
    F.  COMPONENTS/PARTS IN WORK (DEPOT LEVEL AND OTHERS) - 
DEPOT AND OTHER MAINTENANCE ACTIVITY COMMANDERS WILL ENSURE ITEMS 
LISTED IN PARAGRAPH 7 ARE NOT ISSUED UNTIL THEY ARE IN COMPLIANCE 
WITH THIS MESSAGE. 
2.  TASK/INSPECTION SUSPENSE DATE - COMPLETE THE INSPECTION IAW 
PARAGRAPH 8 WITHIN THE NEXT 10 FLIGHT HOURS, BUT NLT 7 AUG 02.  
REPLACE UNTESTED P/N 114C3044-2 AFT YOKE SUPPORT SHAFT AT THE 
NEXT PHASE INSPECTION INTERVAL, OR 31 DECEMBER 2002, WHICHEVER 
OCCURS FIRST.  REPORT IAW PARAGRAPH 14A(2) NLT 12 AUG 02.
3.  TAMMS REPORTING COMPLIANCE SUSPENSE DATE - REPORT COMPLIANCE 
IAW PARA 14A(1) NLT 31 JUL 02.
4.  SUMMARY OF PROBLEM - 
                             NOTE 
            CRITICAL SAFETY ITEMS (CSI) WERE PREVIOUSLY 
            KNOWN AS FLIGHT SAFETY PARTS (FSP). 
    A.  THE ORIGINAL QUALIFICATION (FATIGUE TESTING) OF CRITICAL 
SAFETY ITEMS (CSI) WAS DONE BY BOEING HELICOPTERS UNDER ARMY 
DIRECTION.  THE FATIGUE TESTING OF THESE PARTS SUBSTANTIATED 
THEIR SERVICE LIFE AND THE PARTS DESIGN WAS CONSIDERED QUALIFIED.  
IN OCTOBER 1995, A CHANGE IN THE ARMY FLIGHT SAFETY PART (FSP) 
POLICY REQUIRED THAT PARTS MANUFACTURED BY AUTHORIZED 
VENDORS/SUPPLIERS AND ORIGINALLY QUALIFIED BY THE PRIME 
CONTRACTOR MUST BE FATIGUE TESTED.  THE H-47 AFT YOKE SUPPORT 
SHAFT, P/N 114C3044-2 IS A CRITICAL SAFETY ITEM (CSI).  THE 
114C3044-2 SHAFT IS USED TO ATTACH THE YOKE ASSEMBLY, P/N 
114C3043-6 TO THE AIRFRAME.  FAILURE OF THIS SHAFT WOULD RESULT 
IN LOSS OF CONTROL TO THE AFT ROTOR HEAD.  SOME 114C3044-2 SHAFTS 
WERE FIELDED WITHOUT BEING QUALIFIED AS AN ALTERNATE SOURCE BY 
FATIGUE TESTING. 
    B.  MANPOWER/DOWNTIME AND FUNDING IMPACTS - SEE PARA 12.
    C.  THE PURPOSE OF THIS MESSAGE IS TO - 
        (1)  INSPECT ALL 114C3044-2 AFT YOKE SUPPORT SHAFTS 
INSTALLED ON H-47 SERIES AIRCRAFT AND IN STOCK. 
        (2)  REPLACE ALL 114C3044-2 AFT YOKE SUPPORT SHAFTS THAT 
DO NOT EXHIBIT A QUALIFIED AND FATIGUE TESTED CAGE CODE OR 
MANUFACTURERS NAME ON THE SHAFTS AT THE NEXT PHASE INSPECTION, OR 
31 DECEMBER 2002, WHICHEVER OCCURS FIRST.  
5.  END ITEMS TO BE INSPECTED - ALL H-47 SERIES AIRCRAFT.   
6.  ASSEMBLY COMPONENTS TO BE INSPECTED - N/A. 
7.  PARTS TO BE INSPECTED -
    NOMENCLATURE             PART NO.            NSN 
SHAFT, AFT YOKE SUPPORT    114C3044-2      1560-00-868-8468 
8.  INSPECTION PROCEDURES - 
                             NOTE 
            READ ALL PARAGRAPH 8 INSPECTION PROCEDURES 
            PRIOR TO PROCEEDING TO PARAGRAPH 9 CORRECTION 
            PROCEDURES. 
    A.  LOCATE THE 114C3044-2 SHAFT, AFT YOKE SUPPORT.  FOR 
C/MH-47D, REFER TO TM 55-1520-240-23P, 1 NOV 1989, FIGURE 376, 
ITEM 83, OR TM 55-1520-240-23P, 24 MAY 2002, FIGURE 376, ITEM 73.  
FOR MH-47E, REFER TO TM 1-1520-252-23P, FIGURE 11-16, ITEM 78. 
                             NOTE 
            THERE MAY BE TWO DIFFERENT FIVE DIGIT CODES 
            MARKED ON THE SUBJECT SHAFTS.  THE FIVE DIGIT 
            CODE 81996 IS NOT THE MANUFACTURERS CAGE CODE.  
            IF SO MARKED, THE NUMBER 81996 IDENTIFIES THE 
            PART AS HAVING BEEN MANUFACTURED IAW A GOVERNMENT 
            TECHNICAL DATA PACKAGE (TDP).  USE THE FIVE DIGIT 
            CODES IAW PARAGRAPH 8B BELOW TO DETERMINE THE 
            MANUFACTURERS CODE. 
    B.  IDENTIFY THE FIVE DIGIT MANUFACTURERS CAGE CODE ON THE 
END OF THE SHAFT.  IF THE END OF THE SHAFT IS MARKED WITH ONE OF 
THE FOLLOWING CAGE CODES OR MANUFACTURERS NAME, THE 114C3044-2 
SHAFT HAS BEEN FATIGUE TESTED AND IS QUALIFIED. 
        (1)  CAGE CODE 77272 (BOEING).
        (2)  CAGE CODE 7D072 (TURA MACHINE COMPANY).
        (3)  CAGE CODE 07952 (RUSCOMB TOOL AND MACHINE CO.).
    C.  IF THE END OF THE SHAFT IS MARKED WITH CAGE CODES 77272, 
7D072, 07952 OR CORRESPONDING MANUFACTURERS NAME, THE 114C3044-2 
SHAFT IS SERVICEABLE.  CLEAR THE RED HORIZONTAL DASH //-// STATUS 
SYMBOL ENTRY AND ENTER COMPLIANCE WITH CH-47-02-ASAM-04 (TB 1-
1520-240-20-149) ON THE DA FORM 2408-15.  
    D.  IF THE END OF THE SHAFT IS MARKED WITH A CAGE CODE OR 
MANUFACTURERS NAME OTHER THAN THE THREE IDENTIFIED IN PARAGRAPH 
8B ABOVE, OR IF THE CAGE CODE AND MANUFACTURERS NAME CANNOT BE 
IDENTIFIED, THE SHAFT IS UNSERVICEABLE.  PROCEED TO PARAGRAPH 9A 
BELOW.
9.  CORRECTION PROCEDURES - 
    A.  REMOVE AND REPLACE ANY UNSERVICEABLE SHAFT WITH A SHAFT 
FROM THE SUPPLY SYSTEM THAT IS SERVICEABLE AS DEFINED IN 
PARAGRAPH 8B ABOVE.  THE RED HORIZONTAL DASH //-// STATUS SYMBOL 
WILL BE CLEARED AND THE FOLLOWING ENTRY MADE ON THE DA FORM 2408-
13-1 "REPLACE UNTESTED P/N 114D3044-2 AFT YOKE SUPPORT SHAFT AT 
THE NEXT PHASE INSPECTION INTERVAL, OR 31 DECEMBER 2002, 
WHICHEVER OCCURS FIRST" WITH A RED DIAGONAL "/" STATUS SYMBOL. 
    B.  PREPARE THE AIRCRAFT FOR SAFE GROUND MAINTENANCE. 
    C.  LOCATE THE 114C3044-2 SHAFT, AFT YOKE SUPPORT.  FOR C/MH-
47D, REFER TO TM 55-1520-240-23P, 1 NOV 1989, FIGURE 376, ITEM 
83, OR TM 55-1520-240-23P, 24 MAY 2002, FIGURE 376, ITEM 73. FOR 
MH-47E, REFER TO TM1-1520-252-23P, FIGURE 11-16, ITEM 78. 
    D.  REPLACE THE 114C3044-2 SHAFT, AFT YOKE SUPPORT.  FOR 
C/MH-47D, REFER TO TM 55-1520-240-23, TASK 11-227 (REMOVAL) AND 
TASK 11-233 (INSTALL), OR FOR MH-47E, REFER TO TM 1-1520-252-23, 
TASK 11-245 (REMOVAL) AND TASK 11-251 (INSTALL).  
10.  SUPPLY/PARTS AND DISPOSITION -
     A.  PARTS REQUIRED - ITEMS CITED IN PARAGRAPHS 12C MAY BE 
REQUIRED TO REPLACE DEFECTIVE ITEMS.
     B.  REQUISITIONING INSTRUCTIONS - REQUISITION REPLACEMENT 
PARTS USING NORMAL SUPPLY PROCEDURES.  ALL REQUISITIONS SHALL USE 
PROJECT CODE (CC 57-59) "X1Z" (X-RAY-ONE-ZULU). 
                              NOTE 
            PROJECT CODE "X1Z" IS REQUIRED TO TRACK 
            AND ESTABLISH A DATA BASE OF STOCK FUND 
            EXPENDITURES INCURRED BY THE FIELD AS A 
            RESULT OF SOF AND ASAM ACTIONS.
     C.  BULK AND CONSUMABLE MATERIALS -
    NOMENCLATURE      PART NO./NSN      QTY     
  COTTER PIN         MS24665-379        1     
                       5315-00-059-0494
  NUT, PLAIN         MS21025-20         1     
                       5310-00-838-0265
     D.  DISPOSITION - DEMILITARIZE/MUTILATE IAW TM 1-1500-328-23 
ANY PART/COMPONENT WHICH DOES NOT MEET INSPECTION CRITERIA. 
     E.  DISPOSITION OF HAZARDOUS MATERIAL - N/A. 
11.  SPECIAL TOOLS AND FIXTURES REQUIRED - N/A. 
12.  APPLICATION -
     A.  CATEGORY OF MAINTENANCE - AVUM.  AIRCRAFT DOWNTIME WILL 
BE CHARGED TO AVUM MAINTENANCE.  REPORT AIRCRAFT NON-MISSION 
CAPABLE MAINTENANCE (NMCM) WHILE UNDERGOING INSPECTION AND 
CORRECTION IAW THIS ASAM.  REPORT AIRCRAFT NON-MISSION CAPABLE 
SUPPLY (NMCS) WHILE WAITING FOR PARTS IAW THIS ASAM.
     B.  ESTIMATED TIME REQUIRED - 
         (1)  TIME TO COMPLETE INSPECTION - 
              (A)  TOTAL OF 0.5 MAN-HOURS USING 1 PERSON.
              (B)  TOTAL OF 0 HOURS DOWNTIME FOR ONE END ITEM.
         (2)  TIME FOR REPLACEMENT - 
              (A)  TOTAL OF 36 MAN-HOURS USING 3 PERSONS.
              (B)  TOTAL OF 12 HOURS DOWNTIME FOR ONE END ITEM.
     C.  ESTIMATED COST IMPACT TO THE FIELD - 
NOMENCLATURE      PART NO./NSN      QTY     COST EA.    TOTAL $
SHAFT, YOKE        114C3044-2         1     $305.53     $305.53
                1560-00-868-8468 
COTTER PIN         MS24665-379        1     $  7.20     $  7.20
                5315-00-059-0494
NUT, PLAIN         MS21025-20         1     $ 13.17     $ 13.17
                5310-00-838-0265
                              TOTAL COST PER AIRCRAFT = $325.90
     D.  TB/MWOS TO BE APPLIED PRIOR TO OR CONCURRENTLY WITH THIS 
INSPECTION - N/A. 
     E.  PUBLICATIONS WHICH REQUIRE CHANGE AS A RESULT OF THIS 
INSPECTION - N/A. 
13.  REFERENCES - 
     A.  DA PAM 738-751, 15 MAR 99.
     B.  TM 55-1520-240-23P. 
     C.  TM 55-1520-240-23. 
     D.  TM 1-1520-252-23P. 
     E.  TM 1-1520-252-23. 
     F.  TM 1-1520-328-23. 
14.  RECORDING AND REPORTING REQUIREMENTS -
     A.  AIRCRAFT - 
         (1)  TAMMS REPORTING COMPLIANCE SUSPENSE - UPON ENTERING 
REQUIREMENTS OF THIS ASAM ON DA FORM 2408-13-1 FOR ALL EFFECTED 
AIRCRAFT, COMMANDERS WILL FORWARD A PRIORITY MESSAGE, DATAFAX OR 
E-MAIL TO CDR, AMCOM, ATTN:  AMSAM-SF-A (SOF COMPLIANCE OFFICER), 
REDSTONE ARSENAL, AL 35898-5000, IAW AR 95-1, NLT DATE SPECIFIED 
IN PARAGRAPH 3 ABOVE.  DATAFAX NUMBER IS DSN 897-2111 OR 
(256) 313-2111.  E-MAIL ADDRESS IS "SAFEADM@REDSTONE.ARMY.MIL".  
THE REPORT WILL CITE THIS ASAM AND TB NUMBER, DATE OF ENTRY IN 
DA FORM 2408-13-1, THE AIRCRAFT MISSION DESIGN SERIES AND SERIAL 
NUMBERS OF AIRCRAFT IN NUMERICAL ORDER.
         (2)  TASK/INSPECTION REPORTING SUSPENSE - UPON 
COMPLETION OF INSPECTION, COMMANDERS WILL FORWARD A PRIORITY 
MESSAGE TO THE LOGISTICAL POINT OF CONTACT LISTED IN PARAGRAPH 
16B BELOW.  THE REPORT WILL CITE THIS ASAM AND TB NUMBER, DATE OF 
INSPECTION, AIRCRAFT SERIAL NUMBER, AIRCRAFT AND COMPONENT HOURS, 
AND RESULTS OF THE INSPECTION.  INSPECTION AND REPORTS WILL BE 
COMPLETED NLT DATE SPECIFIED IN PARAGRAPH 2 ABOVE. 
     B.  WHOLESALE SPARE PARTS/ASSEMBLIES - 
         (1)  REPORTING ASAM RECEIPT - N/A. 
         (2)  TASK/INSPECTION REPORTING SUSPENSE - N/A.  
     C.  RETAIL SPARE PARTS/ASSEMBLIES - 
         (1)  REPORTING ASAM RECEIPT - N/A.
         (2)  TASK/INSPECTION REPORTING SUSPENSE - COMMANDERS AND 
FACILITY MANAGERS WILL REPORT INSPECTION RESULTS TO THE 
LOGISTICAL POINT OF CONTACT IN PARAGRAPH 16B BELOW NLT DATE 
SPECIFIED IN PARAGRAPH 1E(2).  REPORT THE QUANTITY INSPECTED BY 
CONDITION CODE AND THE RESULTING CONDITION CODE.  REPORT BY 
E-MAIL OR DATAFAX AND PROVIDE LOCAL POINT OF CONTACT.
     D.  THE FOLLOWING FORMS ARE APPLICABLE AND ARE TO BE 
COMPLETED IAW DA PAM 738-751, 15 MAR 99 - 
                             NOTE 
            ULLS-A USERS WILL USE APPLICABLE "E" FORMS.
          (1)  DA FORM 2408-13, AIRCRAFT STATUS INFORMATION 
RECORD.
          (2)  DA FORM 2408-13-1, AIRCRAFT INSPECTION AND 
MAINTENANCE RECORD.
          (3)  DA FORM 2408-15, HISTORICAL RECORD FOR AIRCRAFT.
          (4)  DD FORM 1574/DD FORM 1574-1, SERVICEABLE TAG/LABEL - 
MATERIEL (COLOR YELLOW).  ANNOTATE REMARKS BLOCK WITH "INSPECTED 
SERVICEABLE IAW CH-47-02-ASAM-04, (TB 1-1520-240-20-149)."
          (5)  DD FORM 1577/DD FORM 1577-1, UNSERVICEABLE 
(CONDEMNED) TAG/LABEL - MATERIEL (COLOR RED).  ANNOTATE REMARKS 
BLOCK WITH "CONDEMNED IAW CH-47-02-ASAM-04, (TB 1-1520-240-20-149) 
AND MUTILATED IAW TM 1-1500-328-23." 
          15.  WEIGHT AND BALANCE - N/A.
16.  POINTS OF CONTACT - 
     A.  TECHNICAL POINT OF CONTACT FOR THIS MESSAGE IS MR. LARRY 
WIESCHHAUS, H-47 TEAM LEADER, AMSAM-RD-AE-I-P-C, DSN 897-2350, 
EXTENSION 9866 OR (256) 705-9866.  DATAFAX IS (256) 705-9918.  
E-MAIL IS "LARRY.WIESCHHAUS@RDEC.REDSTONE.ARMY.MIL". 
     B.  LOGISTICAL POINT OF CONTACT FOR THIS MESSAGE IS BILL 
OLSON, SFAE-AV-CH-L (CUSTOMER SERVICE TEAM), DSN 897-3379 OR 
(256) 313-3379, DATAFAX IS DSN 897-4348 OR (256) 313-3348.  
E-MAIL IS "WILLIAM.OLSON@PEOAVN.REDSTONE.ARMY.MIL".
     C.  WHOLESALE MATERIEL POINT OF CONTACT (SPARES) IS MR. PAUL 
HUGHES, DLA, DSN 695-6328 OR (804) 279-6328, DATAFAX IS DSN 695-
5695.  E-MAIL IS "PAUL.HUGHES@DSCR.DLA.MIL".
     D.  FORMS AND RECORDS POINT OF CONTACT FOR THIS MESSAGE IS 
MS. ANN WALDECK, AMSAM-MMC-MA-NM, DSN 746-5564 OR (256) 876-5564.  
DATAFAX IS DSN 746-4904 OR (256) 876-4904.  E-MAIL IS 
"ANN.WALDECK@REDSTONE.ARMY.MIL".
     E.  SAFETY POINTS OF CONTACT ARE -
         (1)  PRIMARY - MR. FRANK ROSEBERY (SAIC), AMSAM-SF-A, 
DSN 788-8631 OR (256) 842-8631.  DATAFAX IS DSN 897-2111 OR (256) 
313-2111.  E-MAIL IS "FRANK.ROSEBERY@REDSTONE.ARMY.MIL".
         (2)  ALTERNATE - MR. RUSS PEUSCH, AMSAM-SF-A, DSN 788-
8632 OR (256) 842-8632.  DATAFAX IS DSN 897-2111 OR (256) 313-
2111.  E-MAIL IS "RUSSELL.PEUSCH@REDSTONE.ARMY.MIL".
     F.  FOREIGN MILITARY SALES RECIPIENTS REQUIRING 
CLARIFICATION OF ACTION ADVISED BY THIS MESSAGE SHOULD CONTACT 
MR. RONNIE W. SAMMONS, AMSAM-SA-AS-UT, DSN 897-0407 OR (256) 313-
0407.  DATAFAX IS DSN 897-0411 OR (256) 313-0411.  EMAIL IS 
"RONNIE.SAMMONS@REDSTONE.ARMY.MIL".
     G.  AFTER HOURS CONTACT THE AMCOM OPERATIONS CENTER (AOC) 
DSN 897-2066/7 OR (256) 313-2066/7.